SIKA PRODUCTS
RANGE:
| SIKAFLEX
- PRO - POLYURETHANE JOINT SEALANT |
Description: |
|
| Sikaflex-PRO
is a one-component thixotropic, polyurethane based joint
sealant. It cures under the influence of atmospheric
moisture to form an elastomeric material with adhesive
properties, in some cases without the need for priming
of the substrate. |
Uses: |
·
·
·
·
·
·
·
·
·
·
·
·
|
Expansion
joints in buildings and civil structures above
and below ground
Construction joints
Joints in precast concrete elements
External wall cladding and cladding joints
Infill panel joints
Curtain walling
Water retaining structures for potable water
Sanitary installations
Sealing around window and door frames
Flexible draught proofing
Sealing penetrations in walls or floors for ducts, piping,
etc.
Retaining walls |
Features & Benefits: |
·
·
·
·
·
·
·
·
·
·
·
·
|
Excellent
adhesion on all cement based materials, brick, ceramics,
polyurethane, epoxy, most polyesters, most metals and
most timbers
High durability
Good weathering resistance
Non-sag on vertical and soffit joints up to 30mm width
Short skinning time
Short cut off string, even after storage
Ready for immediate use - no mixing, saves time
No potential mixing errors or wastage due to mixed quantities
being greater than required
Non-corrosive
Can be painted over with many water, solvent and rubber
based paints (preliminary testing recommended)
New Sikaflex-PRO will bond to well cleaned out old Sikaflex
Certified for use with potable water
Download:
Sikaflex PRO data sheet
We have many customers saying how cheap we sell
Sikaflex for compared to large HARDWARE stores, and
we are!!!!
310ml Cartridges
- $11.30(+GST)
600ml Sausages - $16.00(+GST)
The price may
vary depending on quantity sold to you as well.
|
|
| SIKAFLEX
- 11 FC POLYURETHANE
JOINT SEALANT/ADHESIVE |
Description: |
 |
| Sikaflex-11
FC is a fast curing polyurethane sealant/adhesive with
permanent elasticity. It cures under the influence of
atmospheric moisture to form an elastomeric material
with adhesive properties. 'FC' stands for 'Fast Cure',
any polyurethane Fast Cure is also classified as an
adhesive as well as a sealant. |
Uses: |
·
·
·
·
·
·
·
·
·
·
·
·
·
|
As
an elastic adhesive for:
Assembling metal framed buildings
Cover plates and coverings
Light-weight construction materials
Acoustic ceiling tiles
Wood, metal or plastic window and door frames
Floor mouldings and door sills
As an elastic joint sealant for:
Sealing joints in concrete, epoxy, stone and quarry
tiled floors
Sealing joints in roofing and guttering, etc.
Flexible draught proofing
Containers, water tanks and silos
Bolted lap joints
Sealing penetrations in walls or floors for ducts, piping,
etc.
Sanitary purposes
|
Features
& Benefits:
|
·
·
·
·
·
·
·
·
·
·
·
|
New
Sikaflex-will bond to well cleaned out old Sikaflex
Excellent adhesion on all cement based materials, brick,
ceramics, metals, wood, polyurethane, epoxy, and some
polyesters
Fast cure rate
High durability
High abrasion resistance and tough wear strength
Good weathering and water resistance
Non-sag on vertical joints up to 30mm width
Ready for immediate use - no mixing
Non-corrosive
Can be painted over with many water, solvent and rubber-based
paints (preliminary tests recommended)
Certified for use in contact with potable water
Download:
Sikaflex 11FC data sheet
|
| SIKAFLEX
TANK - CHEMICAL RESISTANT POLYURETHANE JOINT SEALANT |
Description: |
|
| Sikaflex-Tank
is a one component, thixotropic, polyurethane based joint
sealant. It is used in areas for storage, filling and
handling of contaminated water and other liquids. |
Uses: |
·
*Floor and perimeter
joints in areas exposed to chemicals.
· *Facilities
for storage, filling and handling of contaminated water
and ***other liquids
in filling stations, handling areas/yards, storage tanks
***and bunds, barrel stores.
· *Floor
joints in petrol stations.
· *Floor
and connection joints (workshops, car parks etc).
· *Sealing
joints in water retaining structures (sewerage and water
***treatment plants, filtration
and aeration tanks). |
Advantages: |
| ·
·
·
·
·
·
·
·
·
|
One-component,
ready-to-use.
Excellent chemical resistance to a wide variety of liquids.
High mechanical resistance.
High tear propagation resistance.
Non-sagging.
Excellent movement capacity.
Non-corrosive.
Movement capability 25%
Resistant to bacterial attack
Download:
Sikaflex TANK Data Sheet
|
| SIKA
PRIMERS for POLYURETHANE JOINT SEALING |
Description: |
|
| Sika
polyurethane primers are used to achieve maximum substrate
adhesion. If you need your polyurethane to stick well,
this is the professionals choice. Not all joints or fillets
require this material but it always helps. The primers
are painted onto the substrate which creates a excellent
bond compared to using the joint sealant on the bare substrate. |
Uses: |
|
Waterproofing
Warehouse stocks many Sika primers to
satisfy customers application needs:-
· Primer 1/202 - Used for general porous
substrates, e.g. concrete
· Primer 206 G + P - Used for Glass
and Panel substrates
· Primer 3 - Used for damp concrete
situations where the concrete **has
not cured yet or an area that cannot be dried quickly
· Primer 290DC/215 - Used on timber
substrates
**and many more.
**All primers available
on order if not already in stock.
Download:
Sika Primer Selection Guide (2006 Guide)
Download:
Sika Primer Selection Guide - 2007 Update
We also carry Sika Colma Cleaner
for cleaning tools after polyurethane joint sealant
applications. |
Coverage: please see the 'Joint
Sealant Quantity Estimation Chart' (on this
website)
For more generalised info on Sika Polyurethanes and Epoxy
Resins download the following data sheets - 'Sikaflex
General'(polyurethane) or 'Sika
Elastomeric Sealant Guide' for more technical information.
Also available is the 'Sikadur
General' guide for epoxy resins.
|
| SIKADUR
- 31N |
Description: |
|
| Sikadur-31
is a thixotropic adhesive mortar based on a 2-component
solvent free epoxy resin containing fillers. Sikadur-31
will bond and fill a wide variety of building and construction
materials and may be used in both dry and damp conditions
thereby providing an adhesive mortar ideally suited to
site applications. It is available in three grades: rapid,
normal and long potlife for low, medium and high temperatures
respectively. |
Uses: |
| Sikadur-31
may be used as a thin layer levelling mortar, repair mortar
or adhesive for most building materials (concrete, brick,
stone, ceramics, cement mortar, GRC, fibrous cement, iron
and steel and epoxy mortar). Sikadur-31 may also be used
to anchor holding down bolts, starter bars etc. as a bonding
bridge between old concrete and Sikadur-41 mortar. The
material is ideally suited for bonding of external reinforcement
and as a general structural adhesive. Special higher strength
grades of material are available for segmental bridge
and other construction. |
Features & Benefits: |
| ·
·
·
·
·
·
·
·
·
·
·
·
· |
Chemical
resistance
Insensitive to moisture during application, cure or whilst
in service
Application at low temperatures
Excellent adhesion to most building materials even when
damp
High abrasion resistance
Approved for use in contact with potable water
High early strength
High tensile and flexural strength
Supplied in factory proportioned units
Easily applied - thixotropic, non-sag
Proven in service
Shrink free
Two component of different colours enabling visual control
of degree of mixing
Download:
Sikadur 31N data sheet
Sikadur 31N
- Part of the Sika COMBIFLEX SYSTEM |
| |
|
| SIKADUR
COMBIFLEX SYSTEM |
Description: |
|
| The
Sikadur-Combiflex joint sealing system consists of two products:
· *Sikadur-31
Adhesive (Normal, Long Potlife or Rapid) - the product ***above,
and
· *Combiflex (SikaNorm-Hypalon).
Sikadur-31 Adhesive is epoxy resin based and establishes a strong
bond to the substrate and the Combiflex (SikaNorm-Hypalon) is
a highly elastic, rot-proof and chemically and UV resistant
sheet membrane with a thickness of 1 mm or
2 mm.
Sikadur-Combiflex can be applied on dry or damp substrates.
It shows remarkable adhesion to concrete, iron and steel and
is perfect for joints with very large expansion.
Sikadur-Combiflex is also weather and waterproof. The Sikadur-Combiflex
system is approved for potable water contact. |
| Uses: |
·
*Sealing internal joints in new or
refurbished concrete water tanks, ***reservoirs,
pipelines, sewers and swimming pools.
· *Joints in bunds
and tanks for heating oil and fuel oil, etc.
· *Sealing underwater
joints in situ.
· *Sealing joints
in large decks of multi-storey car parks.
· *Sealing joints
in tunnels, silos and roofs.
· *Sealing and repairing
joints that have more movement than can be ***accommodated
by conventional elastomeric wet applied sealants. |
Features & Benefits: |
| ·
·
·
·
·
·
·
·
·
·
·
· |
Applicable
on dry and damp surfaces
Quick hardening in low temperatures
Three adhesive types for application between 5°C and 45°C
For large expansion joints or cracks
Of permanent elasticity even at low temperatures
Weather resistant
Water resistant
Rot resistant
Resistance against many chemicals
Excellent adhesion to most conventional building materials
Perforations along edges of Combiflex provide “rivet effect” and
adds mechanical fixing to augment chemical bond
No need to remove failed sealant from old joints before use.
Download:
Sikadur Combiflex data sheet
See our SIKA COMBIFLEX SCENARIO PAGE
|
| SIKADUR
- 52N |
Description: |
|
| Sikadur-52
is a low viscosity, free flowing and fast curing injection resin
and primer/coating based on a 2 component solvent free epoxy resin;
ideally suited to a wide range of building and civil engineering
applications where highly penetrative material is required. It
is available in two grades, Normal and Long Potlife for moderate
and high ambient temperatures respectively. |
Uses: |
Sikadur-52
may be used to inject and fill cracks between 0.2 - 5 mm wide
in a wide variety of constructions applications. Sikadur-52 does
not shrink on curing and forms a rigid, high strength product
which exhibits excellent adhesion to most construction materials
enabling the restoration of structural adequacy to columns, beams,
foundations, decks and water retaining structures.
Due to its highly penetrative nature Sikadur-52 is ideally suited
for application as a primer beneath Sikadur epoxy mortars or Sikafloor
mortars and coatings on dense substrates. Sikadur-52 may also
be used to stabilise weak and friable substrates. Special high
strength grades can be made to order. |
Features & Benefits: |
| ·
·
·
·
·
·
·
·
·
·
|
Shrink
free
Insensitive to moisture during application, cure or whilst in
service
Applicable over wide temperature range
Low viscosity
Excellent adhesion to most building materials even when damp
Proven in service
High tensile and flexural strength
Supplied in factory proportioned units
High early strength
Chemical resistant
Download:
Sikadur 52N Data Sheet
|
| SIKAGROUT
GP |
Description: |
|
SikaGrout
GP is a general purpose cementitious grout that is shrinkage
compensated.
SikaGrout GP is a blend of Portland cement, carefully selected
and graded
aggregates and admixtures. |
Uses: |
· *General purpose
grouting.
· *Machine and structural
base plants.
· *Anchor bolts.
· *Pre-cast concrete
sections.
· *Cavities, gaps
and recesses. |
Features & Benefits: |
·
·
·
·
· |
Shrinkage
compensating properties.
Similar appearance to concrete.
Contains no chlorides, or corrosive ingredients.
Can be dry packed, rammed, trowelled, poured or pumped.
Type ‘A’ grout according to MP20 Part 3 – 1977.
Download: SikaGrout GP Data Sheet
Download: Sika GROUT SELECTION GUIDE
|
|
